Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port
Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port
brand: DIYTECH SKU:DT3164-03
Regular price
$18.69
- guaranteeQuality checked
- Special gift cardsSpecial gift cards
- Free return Within 60 days
- Consultancyservice@diytech.cc
Features:
1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.
?2. Default serail port setting : 9600, N, 8, 1
3. Pairing code : 1234
4. Running in slave role: Pair with BT dongle and master module
5. Coupled Mode: Two modules will establish communication automatically when powered.
6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.
Parameters:
1. Bluetooth protocal : Bluetooth Specification v2.0+EDR
2. Frequency : 2.4GHz ISM band
3. Modulation : GFSK(Gaussian Frequency Shift Keying)
4. Emission power : <=4dBm, Class 2
5. Sensitivity : <=-84dBm at 0.1% BER
6. Speed : Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps
7. Security : Authentication and encryption
8. Profiles : Bluetooth serial port
9. CSR chip : Bluetooth v2.0
10. Wave band : 2.4GHz-2.8GHz, ISM Band
11. Protocol : Bluetooth V2.0
12. Power Class : (+6dbm)
13. Reception sensitivity: -85dBm
14. Voltage : 3.3 to 5V
15. Current : Paring - 35mA, Connected - 8mA
16. Temperature : -40~ +105 Degrees Celsius
17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.
18. Dimension : 26.9mm*13mm*2.2mm
Pin definition:
1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.
2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.
3. PIO11, module state switching pin. HIGH -> response to AT command; LOW or floating -> regular work status.
4. With build-in reset circuit, reset is completed automatically after powered on.
5. Steps to set to MASTER:
6. Set PIO11 HIGH with a 10K resistor in between.
7. Power on, module comes into AT Command Response Status
8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow
Control Method:
1. Via serial port, send characters "AT + ROLE = 1 r n",if successful, return "OK r n", where r n is carriage return.
2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect
?
Package Included:
1*Arduino DB9 RS232 RF Wireless Bluetooth Module
1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.
?2. Default serail port setting : 9600, N, 8, 1
3. Pairing code : 1234
4. Running in slave role: Pair with BT dongle and master module
5. Coupled Mode: Two modules will establish communication automatically when powered.
6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.
Parameters:
1. Bluetooth protocal : Bluetooth Specification v2.0+EDR
2. Frequency : 2.4GHz ISM band
3. Modulation : GFSK(Gaussian Frequency Shift Keying)
4. Emission power : <=4dBm, Class 2
5. Sensitivity : <=-84dBm at 0.1% BER
6. Speed : Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps
7. Security : Authentication and encryption
8. Profiles : Bluetooth serial port
9. CSR chip : Bluetooth v2.0
10. Wave band : 2.4GHz-2.8GHz, ISM Band
11. Protocol : Bluetooth V2.0
12. Power Class : (+6dbm)
13. Reception sensitivity: -85dBm
14. Voltage : 3.3 to 5V
15. Current : Paring - 35mA, Connected - 8mA
16. Temperature : -40~ +105 Degrees Celsius
17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.
18. Dimension : 26.9mm*13mm*2.2mm
Pin definition:
1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.
2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.
3. PIO11, module state switching pin. HIGH -> response to AT command; LOW or floating -> regular work status.
4. With build-in reset circuit, reset is completed automatically after powered on.
5. Steps to set to MASTER:
6. Set PIO11 HIGH with a 10K resistor in between.
7. Power on, module comes into AT Command Response Status
8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow
Control Method:
1. Via serial port, send characters "AT + ROLE = 1 r n",if successful, return "OK r n", where r n is carriage return.
2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect
?
Package Included:
1*Arduino DB9 RS232 RF Wireless Bluetooth Module
Other Customers also buy:
-
$0.06{"id":4518014255191,"title":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port","handle":"arduino-db9-rs232-rf-wireless-bluetooth-module-hc-06-slave-serial-port","description":"\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.\u003cbr\u003e?2. Default serail port setting : 9600, N, 8, 1\u003cbr\u003e3. Pairing code : 1234\u003cbr\u003e4. Running in slave role: Pair with BT dongle and master module\u003cbr\u003e5. Coupled Mode: Two modules will establish communication automatically when powered.\u003cbr\u003e6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eParameters:\u003c\/strong\u003e\u003cbr\u003e1. Bluetooth protocal : Bluetooth Specification v2.0+EDR\u003cbr\u003e2. Frequency : 2.4GHz ISM band\u003cbr\u003e3. Modulation : GFSK(Gaussian Frequency Shift Keying)\u003cbr\u003e4. Emission power : \u0026lt;=4dBm, Class 2\u003cbr\u003e5. Sensitivity : \u0026lt;=-84dBm at 0.1% BER\u003cbr\u003e6. Speed : Asynchronous: 2.1Mbps(Max) \/ 160 kbps, Synchronous: 1Mbps\/1Mbps\u003cbr\u003e7. Security : Authentication and encryption\u003cbr\u003e8. Profiles : Bluetooth serial port\u003cbr\u003e9. CSR chip : Bluetooth v2.0\u003cbr\u003e10. Wave band : 2.4GHz-2.8GHz, ISM Band\u003cbr\u003e11. Protocol : Bluetooth V2.0\u003cbr\u003e12. Power Class : (+6dbm)\u003cbr\u003e13. Reception sensitivity: -85dBm\u003cbr\u003e14. Voltage : 3.3 to 5V\u003cbr\u003e15. Current : Paring - 35mA, Connected - 8mA\u003cbr\u003e16. Temperature : -40~ +105 Degrees Celsius\u003cbr\u003e17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.\u003cbr\u003e18. Dimension : 26.9mm*13mm*2.2mm\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePin definition:\u003c\/strong\u003e\u003cbr\u003e1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.\u003cbr\u003e2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.\u003cbr\u003e3. PIO11, module state switching pin. HIGH -\u0026gt; response to AT command; LOW or floating -\u0026gt; regular work status.\u003cbr\u003e4. With build-in reset circuit, reset is completed automatically after powered on.\u003cbr\u003e5. Steps to set to MASTER:\u003cbr\u003e6. Set PIO11 HIGH with a 10K resistor in between.\u003cbr\u003e7. Power on, module comes into AT Command Response Status\u003cbr\u003e8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eControl Method:\u003c\/strong\u003e\u003cbr\u003e1. Via serial port, send characters \"AT + ROLE = 1 r n\",if successful, return \"OK r n\", where r n is carriage return.\u003cbr\u003e2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect\u003cbr\u003e?\u003cbr\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e1*Arduino DB9 RS232 RF Wireless Bluetooth Module","published_at":"2020-05-20T02:38:34+08:00","created_at":"2020-05-20T02:38:37+08:00","vendor":"DIYTECH","type":"Bluetooth Module","tags":["Arduino","For Arduino","Wireless"],"price":1869,"price_min":1869,"price_max":5548,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32179538526295,"title":"3pcs","option1":"3pcs","option2":null,"option3":null,"sku":"DT3164-03","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port - 3pcs","public_title":"3pcs","options":["3pcs"],"price":1869,"weight":39,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":32179538559063,"title":"10pcs","option1":"10pcs","option2":null,"option3":null,"sku":"DT3164-10","requires_shipping":false,"taxable":false,"featured_image":null,"available":true,"name":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port - 10pcs","public_title":"10pcs","options":["10pcs"],"price":5548,"weight":130,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835"],"featured_image":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835","options":["Batch"],"media":[{"alt":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port","id":6257388060759,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.\u003cbr\u003e?2. Default serail port setting : 9600, N, 8, 1\u003cbr\u003e3. Pairing code : 1234\u003cbr\u003e4. Running in slave role: Pair with BT dongle and master module\u003cbr\u003e5. Coupled Mode: Two modules will establish communication automatically when powered.\u003cbr\u003e6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eParameters:\u003c\/strong\u003e\u003cbr\u003e1. Bluetooth protocal : Bluetooth Specification v2.0+EDR\u003cbr\u003e2. Frequency : 2.4GHz ISM band\u003cbr\u003e3. Modulation : GFSK(Gaussian Frequency Shift Keying)\u003cbr\u003e4. Emission power : \u0026lt;=4dBm, Class 2\u003cbr\u003e5. Sensitivity : \u0026lt;=-84dBm at 0.1% BER\u003cbr\u003e6. Speed : Asynchronous: 2.1Mbps(Max) \/ 160 kbps, Synchronous: 1Mbps\/1Mbps\u003cbr\u003e7. Security : Authentication and encryption\u003cbr\u003e8. Profiles : Bluetooth serial port\u003cbr\u003e9. CSR chip : Bluetooth v2.0\u003cbr\u003e10. Wave band : 2.4GHz-2.8GHz, ISM Band\u003cbr\u003e11. Protocol : Bluetooth V2.0\u003cbr\u003e12. Power Class : (+6dbm)\u003cbr\u003e13. Reception sensitivity: -85dBm\u003cbr\u003e14. Voltage : 3.3 to 5V\u003cbr\u003e15. Current : Paring - 35mA, Connected - 8mA\u003cbr\u003e16. Temperature : -40~ +105 Degrees Celsius\u003cbr\u003e17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.\u003cbr\u003e18. Dimension : 26.9mm*13mm*2.2mm\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePin definition:\u003c\/strong\u003e\u003cbr\u003e1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.\u003cbr\u003e2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.\u003cbr\u003e3. PIO11, module state switching pin. HIGH -\u0026gt; response to AT command; LOW or floating -\u0026gt; regular work status.\u003cbr\u003e4. With build-in reset circuit, reset is completed automatically after powered on.\u003cbr\u003e5. Steps to set to MASTER:\u003cbr\u003e6. Set PIO11 HIGH with a 10K resistor in between.\u003cbr\u003e7. Power on, module comes into AT Command Response Status\u003cbr\u003e8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eControl Method:\u003c\/strong\u003e\u003cbr\u003e1. Via serial port, send characters \"AT + ROLE = 1 r n\",if successful, return \"OK r n\", where r n is carriage return.\u003cbr\u003e2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect\u003cbr\u003e?\u003cbr\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e1*Arduino DB9 RS232 RF Wireless Bluetooth Module"}
-
$0.06{"id":4518014255191,"title":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port","handle":"arduino-db9-rs232-rf-wireless-bluetooth-module-hc-06-slave-serial-port","description":"\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.\u003cbr\u003e?2. Default serail port setting : 9600, N, 8, 1\u003cbr\u003e3. Pairing code : 1234\u003cbr\u003e4. Running in slave role: Pair with BT dongle and master module\u003cbr\u003e5. Coupled Mode: Two modules will establish communication automatically when powered.\u003cbr\u003e6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eParameters:\u003c\/strong\u003e\u003cbr\u003e1. Bluetooth protocal : Bluetooth Specification v2.0+EDR\u003cbr\u003e2. Frequency : 2.4GHz ISM band\u003cbr\u003e3. Modulation : GFSK(Gaussian Frequency Shift Keying)\u003cbr\u003e4. Emission power : \u0026lt;=4dBm, Class 2\u003cbr\u003e5. Sensitivity : \u0026lt;=-84dBm at 0.1% BER\u003cbr\u003e6. Speed : Asynchronous: 2.1Mbps(Max) \/ 160 kbps, Synchronous: 1Mbps\/1Mbps\u003cbr\u003e7. Security : Authentication and encryption\u003cbr\u003e8. Profiles : Bluetooth serial port\u003cbr\u003e9. CSR chip : Bluetooth v2.0\u003cbr\u003e10. Wave band : 2.4GHz-2.8GHz, ISM Band\u003cbr\u003e11. Protocol : Bluetooth V2.0\u003cbr\u003e12. Power Class : (+6dbm)\u003cbr\u003e13. Reception sensitivity: -85dBm\u003cbr\u003e14. Voltage : 3.3 to 5V\u003cbr\u003e15. Current : Paring - 35mA, Connected - 8mA\u003cbr\u003e16. Temperature : -40~ +105 Degrees Celsius\u003cbr\u003e17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.\u003cbr\u003e18. Dimension : 26.9mm*13mm*2.2mm\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePin definition:\u003c\/strong\u003e\u003cbr\u003e1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.\u003cbr\u003e2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.\u003cbr\u003e3. PIO11, module state switching pin. HIGH -\u0026gt; response to AT command; LOW or floating -\u0026gt; regular work status.\u003cbr\u003e4. With build-in reset circuit, reset is completed automatically after powered on.\u003cbr\u003e5. Steps to set to MASTER:\u003cbr\u003e6. Set PIO11 HIGH with a 10K resistor in between.\u003cbr\u003e7. Power on, module comes into AT Command Response Status\u003cbr\u003e8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eControl Method:\u003c\/strong\u003e\u003cbr\u003e1. Via serial port, send characters \"AT + ROLE = 1 r n\",if successful, return \"OK r n\", where r n is carriage return.\u003cbr\u003e2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect\u003cbr\u003e?\u003cbr\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e1*Arduino DB9 RS232 RF Wireless Bluetooth Module","published_at":"2020-05-20T02:38:34+08:00","created_at":"2020-05-20T02:38:37+08:00","vendor":"DIYTECH","type":"Bluetooth Module","tags":["Arduino","For Arduino","Wireless"],"price":1869,"price_min":1869,"price_max":5548,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32179538526295,"title":"3pcs","option1":"3pcs","option2":null,"option3":null,"sku":"DT3164-03","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port - 3pcs","public_title":"3pcs","options":["3pcs"],"price":1869,"weight":39,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":32179538559063,"title":"10pcs","option1":"10pcs","option2":null,"option3":null,"sku":"DT3164-10","requires_shipping":false,"taxable":false,"featured_image":null,"available":true,"name":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port - 10pcs","public_title":"10pcs","options":["10pcs"],"price":5548,"weight":130,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835"],"featured_image":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835","options":["Batch"],"media":[{"alt":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port","id":6257388060759,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.\u003cbr\u003e?2. Default serail port setting : 9600, N, 8, 1\u003cbr\u003e3. Pairing code : 1234\u003cbr\u003e4. Running in slave role: Pair with BT dongle and master module\u003cbr\u003e5. Coupled Mode: Two modules will establish communication automatically when powered.\u003cbr\u003e6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eParameters:\u003c\/strong\u003e\u003cbr\u003e1. Bluetooth protocal : Bluetooth Specification v2.0+EDR\u003cbr\u003e2. Frequency : 2.4GHz ISM band\u003cbr\u003e3. Modulation : GFSK(Gaussian Frequency Shift Keying)\u003cbr\u003e4. Emission power : \u0026lt;=4dBm, Class 2\u003cbr\u003e5. Sensitivity : \u0026lt;=-84dBm at 0.1% BER\u003cbr\u003e6. Speed : Asynchronous: 2.1Mbps(Max) \/ 160 kbps, Synchronous: 1Mbps\/1Mbps\u003cbr\u003e7. Security : Authentication and encryption\u003cbr\u003e8. Profiles : Bluetooth serial port\u003cbr\u003e9. CSR chip : Bluetooth v2.0\u003cbr\u003e10. Wave band : 2.4GHz-2.8GHz, ISM Band\u003cbr\u003e11. Protocol : Bluetooth V2.0\u003cbr\u003e12. Power Class : (+6dbm)\u003cbr\u003e13. Reception sensitivity: -85dBm\u003cbr\u003e14. Voltage : 3.3 to 5V\u003cbr\u003e15. Current : Paring - 35mA, Connected - 8mA\u003cbr\u003e16. Temperature : -40~ +105 Degrees Celsius\u003cbr\u003e17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.\u003cbr\u003e18. Dimension : 26.9mm*13mm*2.2mm\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePin definition:\u003c\/strong\u003e\u003cbr\u003e1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.\u003cbr\u003e2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.\u003cbr\u003e3. PIO11, module state switching pin. HIGH -\u0026gt; response to AT command; LOW or floating -\u0026gt; regular work status.\u003cbr\u003e4. With build-in reset circuit, reset is completed automatically after powered on.\u003cbr\u003e5. Steps to set to MASTER:\u003cbr\u003e6. Set PIO11 HIGH with a 10K resistor in between.\u003cbr\u003e7. Power on, module comes into AT Command Response Status\u003cbr\u003e8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eControl Method:\u003c\/strong\u003e\u003cbr\u003e1. Via serial port, send characters \"AT + ROLE = 1 r n\",if successful, return \"OK r n\", where r n is carriage return.\u003cbr\u003e2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect\u003cbr\u003e?\u003cbr\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e1*Arduino DB9 RS232 RF Wireless Bluetooth Module"}
-
$0.09{"id":4518014255191,"title":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port","handle":"arduino-db9-rs232-rf-wireless-bluetooth-module-hc-06-slave-serial-port","description":"\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.\u003cbr\u003e?2. Default serail port setting : 9600, N, 8, 1\u003cbr\u003e3. Pairing code : 1234\u003cbr\u003e4. Running in slave role: Pair with BT dongle and master module\u003cbr\u003e5. Coupled Mode: Two modules will establish communication automatically when powered.\u003cbr\u003e6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eParameters:\u003c\/strong\u003e\u003cbr\u003e1. Bluetooth protocal : Bluetooth Specification v2.0+EDR\u003cbr\u003e2. Frequency : 2.4GHz ISM band\u003cbr\u003e3. Modulation : GFSK(Gaussian Frequency Shift Keying)\u003cbr\u003e4. Emission power : \u0026lt;=4dBm, Class 2\u003cbr\u003e5. Sensitivity : \u0026lt;=-84dBm at 0.1% BER\u003cbr\u003e6. Speed : Asynchronous: 2.1Mbps(Max) \/ 160 kbps, Synchronous: 1Mbps\/1Mbps\u003cbr\u003e7. Security : Authentication and encryption\u003cbr\u003e8. Profiles : Bluetooth serial port\u003cbr\u003e9. CSR chip : Bluetooth v2.0\u003cbr\u003e10. Wave band : 2.4GHz-2.8GHz, ISM Band\u003cbr\u003e11. Protocol : Bluetooth V2.0\u003cbr\u003e12. Power Class : (+6dbm)\u003cbr\u003e13. Reception sensitivity: -85dBm\u003cbr\u003e14. Voltage : 3.3 to 5V\u003cbr\u003e15. Current : Paring - 35mA, Connected - 8mA\u003cbr\u003e16. Temperature : -40~ +105 Degrees Celsius\u003cbr\u003e17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.\u003cbr\u003e18. Dimension : 26.9mm*13mm*2.2mm\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePin definition:\u003c\/strong\u003e\u003cbr\u003e1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.\u003cbr\u003e2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.\u003cbr\u003e3. PIO11, module state switching pin. HIGH -\u0026gt; response to AT command; LOW or floating -\u0026gt; regular work status.\u003cbr\u003e4. With build-in reset circuit, reset is completed automatically after powered on.\u003cbr\u003e5. Steps to set to MASTER:\u003cbr\u003e6. Set PIO11 HIGH with a 10K resistor in between.\u003cbr\u003e7. Power on, module comes into AT Command Response Status\u003cbr\u003e8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eControl Method:\u003c\/strong\u003e\u003cbr\u003e1. Via serial port, send characters \"AT + ROLE = 1 r n\",if successful, return \"OK r n\", where r n is carriage return.\u003cbr\u003e2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect\u003cbr\u003e?\u003cbr\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e1*Arduino DB9 RS232 RF Wireless Bluetooth Module","published_at":"2020-05-20T02:38:34+08:00","created_at":"2020-05-20T02:38:37+08:00","vendor":"DIYTECH","type":"Bluetooth Module","tags":["Arduino","For Arduino","Wireless"],"price":1869,"price_min":1869,"price_max":5548,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32179538526295,"title":"3pcs","option1":"3pcs","option2":null,"option3":null,"sku":"DT3164-03","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port - 3pcs","public_title":"3pcs","options":["3pcs"],"price":1869,"weight":39,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":32179538559063,"title":"10pcs","option1":"10pcs","option2":null,"option3":null,"sku":"DT3164-10","requires_shipping":false,"taxable":false,"featured_image":null,"available":true,"name":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port - 10pcs","public_title":"10pcs","options":["10pcs"],"price":5548,"weight":130,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835"],"featured_image":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835","options":["Batch"],"media":[{"alt":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port","id":6257388060759,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.\u003cbr\u003e?2. Default serail port setting : 9600, N, 8, 1\u003cbr\u003e3. Pairing code : 1234\u003cbr\u003e4. Running in slave role: Pair with BT dongle and master module\u003cbr\u003e5. Coupled Mode: Two modules will establish communication automatically when powered.\u003cbr\u003e6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eParameters:\u003c\/strong\u003e\u003cbr\u003e1. Bluetooth protocal : Bluetooth Specification v2.0+EDR\u003cbr\u003e2. Frequency : 2.4GHz ISM band\u003cbr\u003e3. Modulation : GFSK(Gaussian Frequency Shift Keying)\u003cbr\u003e4. Emission power : \u0026lt;=4dBm, Class 2\u003cbr\u003e5. Sensitivity : \u0026lt;=-84dBm at 0.1% BER\u003cbr\u003e6. Speed : Asynchronous: 2.1Mbps(Max) \/ 160 kbps, Synchronous: 1Mbps\/1Mbps\u003cbr\u003e7. Security : Authentication and encryption\u003cbr\u003e8. Profiles : Bluetooth serial port\u003cbr\u003e9. CSR chip : Bluetooth v2.0\u003cbr\u003e10. Wave band : 2.4GHz-2.8GHz, ISM Band\u003cbr\u003e11. Protocol : Bluetooth V2.0\u003cbr\u003e12. Power Class : (+6dbm)\u003cbr\u003e13. Reception sensitivity: -85dBm\u003cbr\u003e14. Voltage : 3.3 to 5V\u003cbr\u003e15. Current : Paring - 35mA, Connected - 8mA\u003cbr\u003e16. Temperature : -40~ +105 Degrees Celsius\u003cbr\u003e17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.\u003cbr\u003e18. Dimension : 26.9mm*13mm*2.2mm\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePin definition:\u003c\/strong\u003e\u003cbr\u003e1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.\u003cbr\u003e2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.\u003cbr\u003e3. PIO11, module state switching pin. HIGH -\u0026gt; response to AT command; LOW or floating -\u0026gt; regular work status.\u003cbr\u003e4. With build-in reset circuit, reset is completed automatically after powered on.\u003cbr\u003e5. Steps to set to MASTER:\u003cbr\u003e6. Set PIO11 HIGH with a 10K resistor in between.\u003cbr\u003e7. Power on, module comes into AT Command Response Status\u003cbr\u003e8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eControl Method:\u003c\/strong\u003e\u003cbr\u003e1. Via serial port, send characters \"AT + ROLE = 1 r n\",if successful, return \"OK r n\", where r n is carriage return.\u003cbr\u003e2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect\u003cbr\u003e?\u003cbr\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e1*Arduino DB9 RS232 RF Wireless Bluetooth Module"}
-
$0.11{"id":4518014255191,"title":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port","handle":"arduino-db9-rs232-rf-wireless-bluetooth-module-hc-06-slave-serial-port","description":"\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.\u003cbr\u003e?2. Default serail port setting : 9600, N, 8, 1\u003cbr\u003e3. Pairing code : 1234\u003cbr\u003e4. Running in slave role: Pair with BT dongle and master module\u003cbr\u003e5. Coupled Mode: Two modules will establish communication automatically when powered.\u003cbr\u003e6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eParameters:\u003c\/strong\u003e\u003cbr\u003e1. Bluetooth protocal : Bluetooth Specification v2.0+EDR\u003cbr\u003e2. Frequency : 2.4GHz ISM band\u003cbr\u003e3. Modulation : GFSK(Gaussian Frequency Shift Keying)\u003cbr\u003e4. Emission power : \u0026lt;=4dBm, Class 2\u003cbr\u003e5. Sensitivity : \u0026lt;=-84dBm at 0.1% BER\u003cbr\u003e6. Speed : Asynchronous: 2.1Mbps(Max) \/ 160 kbps, Synchronous: 1Mbps\/1Mbps\u003cbr\u003e7. Security : Authentication and encryption\u003cbr\u003e8. Profiles : Bluetooth serial port\u003cbr\u003e9. CSR chip : Bluetooth v2.0\u003cbr\u003e10. Wave band : 2.4GHz-2.8GHz, ISM Band\u003cbr\u003e11. Protocol : Bluetooth V2.0\u003cbr\u003e12. Power Class : (+6dbm)\u003cbr\u003e13. Reception sensitivity: -85dBm\u003cbr\u003e14. Voltage : 3.3 to 5V\u003cbr\u003e15. Current : Paring - 35mA, Connected - 8mA\u003cbr\u003e16. Temperature : -40~ +105 Degrees Celsius\u003cbr\u003e17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.\u003cbr\u003e18. Dimension : 26.9mm*13mm*2.2mm\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePin definition:\u003c\/strong\u003e\u003cbr\u003e1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.\u003cbr\u003e2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.\u003cbr\u003e3. PIO11, module state switching pin. HIGH -\u0026gt; response to AT command; LOW or floating -\u0026gt; regular work status.\u003cbr\u003e4. With build-in reset circuit, reset is completed automatically after powered on.\u003cbr\u003e5. Steps to set to MASTER:\u003cbr\u003e6. Set PIO11 HIGH with a 10K resistor in between.\u003cbr\u003e7. Power on, module comes into AT Command Response Status\u003cbr\u003e8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eControl Method:\u003c\/strong\u003e\u003cbr\u003e1. Via serial port, send characters \"AT + ROLE = 1 r n\",if successful, return \"OK r n\", where r n is carriage return.\u003cbr\u003e2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect\u003cbr\u003e?\u003cbr\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e1*Arduino DB9 RS232 RF Wireless Bluetooth Module","published_at":"2020-05-20T02:38:34+08:00","created_at":"2020-05-20T02:38:37+08:00","vendor":"DIYTECH","type":"Bluetooth Module","tags":["Arduino","For Arduino","Wireless"],"price":1869,"price_min":1869,"price_max":5548,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32179538526295,"title":"3pcs","option1":"3pcs","option2":null,"option3":null,"sku":"DT3164-03","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port - 3pcs","public_title":"3pcs","options":["3pcs"],"price":1869,"weight":39,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":32179538559063,"title":"10pcs","option1":"10pcs","option2":null,"option3":null,"sku":"DT3164-10","requires_shipping":false,"taxable":false,"featured_image":null,"available":true,"name":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port - 10pcs","public_title":"10pcs","options":["10pcs"],"price":5548,"weight":130,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835"],"featured_image":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835","options":["Batch"],"media":[{"alt":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port","id":6257388060759,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.\u003cbr\u003e?2. Default serail port setting : 9600, N, 8, 1\u003cbr\u003e3. Pairing code : 1234\u003cbr\u003e4. Running in slave role: Pair with BT dongle and master module\u003cbr\u003e5. Coupled Mode: Two modules will establish communication automatically when powered.\u003cbr\u003e6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eParameters:\u003c\/strong\u003e\u003cbr\u003e1. Bluetooth protocal : Bluetooth Specification v2.0+EDR\u003cbr\u003e2. Frequency : 2.4GHz ISM band\u003cbr\u003e3. Modulation : GFSK(Gaussian Frequency Shift Keying)\u003cbr\u003e4. Emission power : \u0026lt;=4dBm, Class 2\u003cbr\u003e5. Sensitivity : \u0026lt;=-84dBm at 0.1% BER\u003cbr\u003e6. Speed : Asynchronous: 2.1Mbps(Max) \/ 160 kbps, Synchronous: 1Mbps\/1Mbps\u003cbr\u003e7. Security : Authentication and encryption\u003cbr\u003e8. Profiles : Bluetooth serial port\u003cbr\u003e9. CSR chip : Bluetooth v2.0\u003cbr\u003e10. Wave band : 2.4GHz-2.8GHz, ISM Band\u003cbr\u003e11. Protocol : Bluetooth V2.0\u003cbr\u003e12. Power Class : (+6dbm)\u003cbr\u003e13. Reception sensitivity: -85dBm\u003cbr\u003e14. Voltage : 3.3 to 5V\u003cbr\u003e15. Current : Paring - 35mA, Connected - 8mA\u003cbr\u003e16. Temperature : -40~ +105 Degrees Celsius\u003cbr\u003e17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.\u003cbr\u003e18. Dimension : 26.9mm*13mm*2.2mm\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePin definition:\u003c\/strong\u003e\u003cbr\u003e1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.\u003cbr\u003e2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.\u003cbr\u003e3. PIO11, module state switching pin. HIGH -\u0026gt; response to AT command; LOW or floating -\u0026gt; regular work status.\u003cbr\u003e4. With build-in reset circuit, reset is completed automatically after powered on.\u003cbr\u003e5. Steps to set to MASTER:\u003cbr\u003e6. Set PIO11 HIGH with a 10K resistor in between.\u003cbr\u003e7. Power on, module comes into AT Command Response Status\u003cbr\u003e8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eControl Method:\u003c\/strong\u003e\u003cbr\u003e1. Via serial port, send characters \"AT + ROLE = 1 r n\",if successful, return \"OK r n\", where r n is carriage return.\u003cbr\u003e2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect\u003cbr\u003e?\u003cbr\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e1*Arduino DB9 RS232 RF Wireless Bluetooth Module"}
-
$0.11{"id":4518014255191,"title":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port","handle":"arduino-db9-rs232-rf-wireless-bluetooth-module-hc-06-slave-serial-port","description":"\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.\u003cbr\u003e?2. Default serail port setting : 9600, N, 8, 1\u003cbr\u003e3. Pairing code : 1234\u003cbr\u003e4. Running in slave role: Pair with BT dongle and master module\u003cbr\u003e5. Coupled Mode: Two modules will establish communication automatically when powered.\u003cbr\u003e6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eParameters:\u003c\/strong\u003e\u003cbr\u003e1. Bluetooth protocal : Bluetooth Specification v2.0+EDR\u003cbr\u003e2. Frequency : 2.4GHz ISM band\u003cbr\u003e3. Modulation : GFSK(Gaussian Frequency Shift Keying)\u003cbr\u003e4. Emission power : \u0026lt;=4dBm, Class 2\u003cbr\u003e5. Sensitivity : \u0026lt;=-84dBm at 0.1% BER\u003cbr\u003e6. Speed : Asynchronous: 2.1Mbps(Max) \/ 160 kbps, Synchronous: 1Mbps\/1Mbps\u003cbr\u003e7. Security : Authentication and encryption\u003cbr\u003e8. Profiles : Bluetooth serial port\u003cbr\u003e9. CSR chip : Bluetooth v2.0\u003cbr\u003e10. Wave band : 2.4GHz-2.8GHz, ISM Band\u003cbr\u003e11. Protocol : Bluetooth V2.0\u003cbr\u003e12. Power Class : (+6dbm)\u003cbr\u003e13. Reception sensitivity: -85dBm\u003cbr\u003e14. Voltage : 3.3 to 5V\u003cbr\u003e15. Current : Paring - 35mA, Connected - 8mA\u003cbr\u003e16. Temperature : -40~ +105 Degrees Celsius\u003cbr\u003e17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.\u003cbr\u003e18. Dimension : 26.9mm*13mm*2.2mm\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePin definition:\u003c\/strong\u003e\u003cbr\u003e1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.\u003cbr\u003e2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.\u003cbr\u003e3. PIO11, module state switching pin. HIGH -\u0026gt; response to AT command; LOW or floating -\u0026gt; regular work status.\u003cbr\u003e4. With build-in reset circuit, reset is completed automatically after powered on.\u003cbr\u003e5. Steps to set to MASTER:\u003cbr\u003e6. Set PIO11 HIGH with a 10K resistor in between.\u003cbr\u003e7. Power on, module comes into AT Command Response Status\u003cbr\u003e8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eControl Method:\u003c\/strong\u003e\u003cbr\u003e1. Via serial port, send characters \"AT + ROLE = 1 r n\",if successful, return \"OK r n\", where r n is carriage return.\u003cbr\u003e2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect\u003cbr\u003e?\u003cbr\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e1*Arduino DB9 RS232 RF Wireless Bluetooth Module","published_at":"2020-05-20T02:38:34+08:00","created_at":"2020-05-20T02:38:37+08:00","vendor":"DIYTECH","type":"Bluetooth Module","tags":["Arduino","For Arduino","Wireless"],"price":1869,"price_min":1869,"price_max":5548,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32179538526295,"title":"3pcs","option1":"3pcs","option2":null,"option3":null,"sku":"DT3164-03","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port - 3pcs","public_title":"3pcs","options":["3pcs"],"price":1869,"weight":39,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":32179538559063,"title":"10pcs","option1":"10pcs","option2":null,"option3":null,"sku":"DT3164-10","requires_shipping":false,"taxable":false,"featured_image":null,"available":true,"name":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port - 10pcs","public_title":"10pcs","options":["10pcs"],"price":5548,"weight":130,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835"],"featured_image":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835","options":["Batch"],"media":[{"alt":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port","id":6257388060759,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.\u003cbr\u003e?2. Default serail port setting : 9600, N, 8, 1\u003cbr\u003e3. Pairing code : 1234\u003cbr\u003e4. Running in slave role: Pair with BT dongle and master module\u003cbr\u003e5. Coupled Mode: Two modules will establish communication automatically when powered.\u003cbr\u003e6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eParameters:\u003c\/strong\u003e\u003cbr\u003e1. Bluetooth protocal : Bluetooth Specification v2.0+EDR\u003cbr\u003e2. Frequency : 2.4GHz ISM band\u003cbr\u003e3. Modulation : GFSK(Gaussian Frequency Shift Keying)\u003cbr\u003e4. Emission power : \u0026lt;=4dBm, Class 2\u003cbr\u003e5. Sensitivity : \u0026lt;=-84dBm at 0.1% BER\u003cbr\u003e6. Speed : Asynchronous: 2.1Mbps(Max) \/ 160 kbps, Synchronous: 1Mbps\/1Mbps\u003cbr\u003e7. Security : Authentication and encryption\u003cbr\u003e8. Profiles : Bluetooth serial port\u003cbr\u003e9. CSR chip : Bluetooth v2.0\u003cbr\u003e10. Wave band : 2.4GHz-2.8GHz, ISM Band\u003cbr\u003e11. Protocol : Bluetooth V2.0\u003cbr\u003e12. Power Class : (+6dbm)\u003cbr\u003e13. Reception sensitivity: -85dBm\u003cbr\u003e14. Voltage : 3.3 to 5V\u003cbr\u003e15. Current : Paring - 35mA, Connected - 8mA\u003cbr\u003e16. Temperature : -40~ +105 Degrees Celsius\u003cbr\u003e17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.\u003cbr\u003e18. Dimension : 26.9mm*13mm*2.2mm\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePin definition:\u003c\/strong\u003e\u003cbr\u003e1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.\u003cbr\u003e2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.\u003cbr\u003e3. PIO11, module state switching pin. HIGH -\u0026gt; response to AT command; LOW or floating -\u0026gt; regular work status.\u003cbr\u003e4. With build-in reset circuit, reset is completed automatically after powered on.\u003cbr\u003e5. Steps to set to MASTER:\u003cbr\u003e6. Set PIO11 HIGH with a 10K resistor in between.\u003cbr\u003e7. Power on, module comes into AT Command Response Status\u003cbr\u003e8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eControl Method:\u003c\/strong\u003e\u003cbr\u003e1. Via serial port, send characters \"AT + ROLE = 1 r n\",if successful, return \"OK r n\", where r n is carriage return.\u003cbr\u003e2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect\u003cbr\u003e?\u003cbr\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e1*Arduino DB9 RS232 RF Wireless Bluetooth Module"}
-
$0.11{"id":4518014255191,"title":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port","handle":"arduino-db9-rs232-rf-wireless-bluetooth-module-hc-06-slave-serial-port","description":"\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.\u003cbr\u003e?2. Default serail port setting : 9600, N, 8, 1\u003cbr\u003e3. Pairing code : 1234\u003cbr\u003e4. Running in slave role: Pair with BT dongle and master module\u003cbr\u003e5. Coupled Mode: Two modules will establish communication automatically when powered.\u003cbr\u003e6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eParameters:\u003c\/strong\u003e\u003cbr\u003e1. Bluetooth protocal : Bluetooth Specification v2.0+EDR\u003cbr\u003e2. Frequency : 2.4GHz ISM band\u003cbr\u003e3. Modulation : GFSK(Gaussian Frequency Shift Keying)\u003cbr\u003e4. Emission power : \u0026lt;=4dBm, Class 2\u003cbr\u003e5. Sensitivity : \u0026lt;=-84dBm at 0.1% BER\u003cbr\u003e6. Speed : Asynchronous: 2.1Mbps(Max) \/ 160 kbps, Synchronous: 1Mbps\/1Mbps\u003cbr\u003e7. Security : Authentication and encryption\u003cbr\u003e8. Profiles : Bluetooth serial port\u003cbr\u003e9. CSR chip : Bluetooth v2.0\u003cbr\u003e10. Wave band : 2.4GHz-2.8GHz, ISM Band\u003cbr\u003e11. Protocol : Bluetooth V2.0\u003cbr\u003e12. Power Class : (+6dbm)\u003cbr\u003e13. Reception sensitivity: -85dBm\u003cbr\u003e14. Voltage : 3.3 to 5V\u003cbr\u003e15. Current : Paring - 35mA, Connected - 8mA\u003cbr\u003e16. Temperature : -40~ +105 Degrees Celsius\u003cbr\u003e17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.\u003cbr\u003e18. Dimension : 26.9mm*13mm*2.2mm\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePin definition:\u003c\/strong\u003e\u003cbr\u003e1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.\u003cbr\u003e2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.\u003cbr\u003e3. PIO11, module state switching pin. HIGH -\u0026gt; response to AT command; LOW or floating -\u0026gt; regular work status.\u003cbr\u003e4. With build-in reset circuit, reset is completed automatically after powered on.\u003cbr\u003e5. Steps to set to MASTER:\u003cbr\u003e6. Set PIO11 HIGH with a 10K resistor in between.\u003cbr\u003e7. Power on, module comes into AT Command Response Status\u003cbr\u003e8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eControl Method:\u003c\/strong\u003e\u003cbr\u003e1. Via serial port, send characters \"AT + ROLE = 1 r n\",if successful, return \"OK r n\", where r n is carriage return.\u003cbr\u003e2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect\u003cbr\u003e?\u003cbr\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e1*Arduino DB9 RS232 RF Wireless Bluetooth Module","published_at":"2020-05-20T02:38:34+08:00","created_at":"2020-05-20T02:38:37+08:00","vendor":"DIYTECH","type":"Bluetooth Module","tags":["Arduino","For Arduino","Wireless"],"price":1869,"price_min":1869,"price_max":5548,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":32179538526295,"title":"3pcs","option1":"3pcs","option2":null,"option3":null,"sku":"DT3164-03","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port - 3pcs","public_title":"3pcs","options":["3pcs"],"price":1869,"weight":39,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":32179538559063,"title":"10pcs","option1":"10pcs","option2":null,"option3":null,"sku":"DT3164-10","requires_shipping":false,"taxable":false,"featured_image":null,"available":true,"name":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port - 10pcs","public_title":"10pcs","options":["10pcs"],"price":5548,"weight":130,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835"],"featured_image":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835","options":["Batch"],"media":[{"alt":"Arduino DB9 RS232 RF Wireless Bluetooth Module HC-06 Slave Serial Port","id":6257388060759,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/diytech.cc\/cdn\/shop\/products\/diymore_20191223114916_kow21.jpg?v=1592419835","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e1. Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.\u003cbr\u003e?2. Default serail port setting : 9600, N, 8, 1\u003cbr\u003e3. Pairing code : 1234\u003cbr\u003e4. Running in slave role: Pair with BT dongle and master module\u003cbr\u003e5. Coupled Mode: Two modules will establish communication automatically when powered.\u003cbr\u003e6. PC hosted mode: Pair the module with bluetooth dongle directly as virtual serial.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eParameters:\u003c\/strong\u003e\u003cbr\u003e1. Bluetooth protocal : Bluetooth Specification v2.0+EDR\u003cbr\u003e2. Frequency : 2.4GHz ISM band\u003cbr\u003e3. Modulation : GFSK(Gaussian Frequency Shift Keying)\u003cbr\u003e4. Emission power : \u0026lt;=4dBm, Class 2\u003cbr\u003e5. Sensitivity : \u0026lt;=-84dBm at 0.1% BER\u003cbr\u003e6. Speed : Asynchronous: 2.1Mbps(Max) \/ 160 kbps, Synchronous: 1Mbps\/1Mbps\u003cbr\u003e7. Security : Authentication and encryption\u003cbr\u003e8. Profiles : Bluetooth serial port\u003cbr\u003e9. CSR chip : Bluetooth v2.0\u003cbr\u003e10. Wave band : 2.4GHz-2.8GHz, ISM Band\u003cbr\u003e11. Protocol : Bluetooth V2.0\u003cbr\u003e12. Power Class : (+6dbm)\u003cbr\u003e13. Reception sensitivity: -85dBm\u003cbr\u003e14. Voltage : 3.3 to 5V\u003cbr\u003e15. Current : Paring - 35mA, Connected - 8mA\u003cbr\u003e16. Temperature : -40~ +105 Degrees Celsius\u003cbr\u003e17. User defined Baud rate : 4800, 9600, 19200, 38400, 57600, 115200, 230400,460800,921600 ,1382400.\u003cbr\u003e18. Dimension : 26.9mm*13mm*2.2mm\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePin definition:\u003c\/strong\u003e\u003cbr\u003e1. PIO8 connects with LED cathodea with 470ohm series resistor in between. LED NEGATIVE connects to ground. It is used to indicate the module state. After powered on, flashing intervals differ in different states.\u003cbr\u003e2. PIO9 is used to control LED indicating paring. It will be steady on when paring is successful.\u003cbr\u003e3. PIO11, module state switching pin. HIGH -\u0026gt; response to AT command; LOW or floating -\u0026gt; regular work status.\u003cbr\u003e4. With build-in reset circuit, reset is completed automatically after powered on.\u003cbr\u003e5. Steps to set to MASTER:\u003cbr\u003e6. Set PIO11 HIGH with a 10K resistor in between.\u003cbr\u003e7. Power on, module comes into AT Command Response Status\u003cbr\u003e8. Open HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity bit, no Flow\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eControl Method:\u003c\/strong\u003e\u003cbr\u003e1. Via serial port, send characters \"AT + ROLE = 1 r n\",if successful, return \"OK r n\", where r n is carriage return.\u003cbr\u003e2. Set PIO11 LOW, re-power, then in Master state, automatically search for slave module and connect\u003cbr\u003e?\u003cbr\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003cbr\u003e1*Arduino DB9 RS232 RF Wireless Bluetooth Module"}